Archive:Kdenlive/Manual/Monitors/uk: Difference between revisions

    From KDE UserBase Wiki
    (Updating to match new version of source page)
    (Updating to match new version of source page)
    Line 66: Line 66:


    Передбачено також '''Монітор запису''', яким можна скористатися для попереднього перегляду [[Special:MyLanguage/Kdenlive/Manual/Capturing|захоплених даних]] з Firewire, ''карток Blackmagic'' або потоків '''FFmpeg''' / '''video4linux'''.
    Передбачено також '''Монітор запису''', яким можна скористатися для попереднього перегляду [[Special:MyLanguage/Kdenlive/Manual/Capturing|захоплених даних]] з Firewire, ''карток Blackmagic'' або потоків '''FFmpeg''' / '''video4linux'''.
    == Separate Clip and Project Monitors ==
    You can click on the Tab names that label the Monitors and drag the monitor out into its own window.
    [[File:Kdenlive monitors seperate with dec.png]]
    To put the monitors back into the Tabbed  view - click on the monitor's title bar and drag the window on top of the other monitor window.
    If the monitor has no title bar (intermittent defect) then you can not do this and you will need to reset kdenlive settings by deleting  ~/.config/kdenliverc


    {{Prevnext2
    {{Prevnext2

    Revision as of 10:30, 29 December 2018

    Other languages:

    Монітори

    Kdenlive uses 2 monitor widgets to display your videos: Clip Monitor and Project Monitor. A third monitor - the Record Monitor - previews video capture. These monitors can be selected by clicking the corresponding tabs which appear at the bottom of the monitor window.

    Resizing the Monitors

    You can resize the monitors by dragging the sizing widget. It is a bit tricky to find the bottom widget. You need to hover just between the bottom of the monitor tab and the timeline

    Монітор кліпу

    На панелі Монітор кліпу буде показано нередагований варіант кліпу, пункт якого позначено на панелі «Дерево проекту».

    Віджети монітора кліпів

    1) Set zone start button - click this to set an 'in' point.

    2) Set zone end button - click this to set an 'out' point.

    3) Zone duration indicator - selected by setting in and out points. Dragging the clip from the clip monitor to the timeline when there is a selected zone causes the selected zone, not the entire clip, to be copied to the timeline.

    4) Position Caret - can be dragged in the clip. (In ver >=0.9.4 and with OpenGL turned on in Settings -> Configure Kdenlive -> Playback, audio will play as you drag this.)

    5) Timecode widget - type a timecode here and hit Enter to go to an exact location in the clip. Timecode is in the format hours:minutes:seconds:frames (where frames will correspond to the number of frames per second in your project profile).

    6) Timecode arrows - can be used to change the current position of the clip in the clip monitor.

    Створення ділянок моніторі кліпів

    Zones are defined regions of clips that are indictated by a colored section in the clip monitor's timeline - see item 3 above. The beginning of a zone is set by clicking [ (item 1 in the pic above). The end of a zone is set by clicking ] (item 2 in the pic above)

    Clip Monitor Right-click menu

    The Clip Monitor has a right-click (context) menu as described here.

    Монітор проекту

    The Project Monitor displays your project's timeline - i.e. the edited version of your video.

    Віджети монітора проекту

    1) The position caret. Shows the current location in the project relative to the whole project. You can click and drag this to move the position in the project.

    2) The timecode widget. You can type a timecode here and press Enter to bring the Project Monitor to an exact location.

    3) Timecode widget control arrows. You can move the Project Monitor one frame at a time with these.

    Створення ділянок на моніторі проекту

    You can use the [ and ] buttons to create a zone in the Project Monitor the same way you make zones in the clip monitor. The zone will be indicated by a colored bar both on the timeline and underneath the Project Monitor.

    Ви можете наказати Kdenlive обробляти лише позначену ділянку (див. обробка позначеної ділянки).

    Контекстне меню монітора проекту

    У програмі передбачено контекстне меню монітора проекту (викликається клацанням правою кнопки миші). Його опис можна знайти тут.

    Монітор запису

    Передбачено також Монітор запису, яким можна скористатися для попереднього перегляду захоплених даних з Firewire, карток Blackmagic або потоків FFmpeg / video4linux.

    Separate Clip and Project Monitors

    You can click on the Tab names that label the Monitors and drag the monitor out into its own window.

    To put the monitors back into the Tabbed view - click on the monitor's title bar and drag the window on top of the other monitor window.

    If the monitor has no title bar (intermittent defect) then you can not do this and you will need to reset kdenlive settings by deleting ~/.config/kdenliverc