Archive:Kdenlive/Manual/Troubleshooting and Common Problems/da: Difference between revisions

From KDE UserBase Wiki
No edit summary
(Updating to match new version of source page)
Line 3: Line 3:
}}
}}
<languages />
<languages />
;Kdenlive warns me about missing codecs, I cannot render in some formats.[[File:MissingCodec.png||right]]
: There are several possible reasons for this:
# You have installed the codecs after Kdenlive's installation. To force Kdenlive to check available codecs on your system, run the configuration wizard: <menuchoice>Settings -> Run Config Wizard</menuchoice>. Complete the wizard and restart Kdenlive to be sure that codecs have been detected.
# The codecs are not available on your system. Kdenlive uses the codecs from your '''FFmpeg''' or '''Libav''' library. Due to some licensing issues, some distributions do not provide all codecs by default and you might need to install an extra package. On Ubuntu / Mint for example, you must install a package called libavcodec-extra-xx. After that, check again the codecs as explained in the first step.
# Last possibility is that your '''FFmpeg''' or '''Libav''' version is buggy and does not report all supported codecs. '''Kdenlive''' releases after 0.9.2 have an option to try using codecs even if they seem unsupported: <menuchoice>Settings -> Configure Kdenlive</menuchoice> and check the <menuchoice>Bypass codec verification</menuchoice> option.


;Kdenlive er for stor på min skærm. Jeg kan ikke gøre den mindre.
;Kdenlive er for stor på min skærm. Jeg kan ikke gøre den mindre.

Revision as of 17:47, 5 February 2013

Information

  • How to file a bug report, and where? How to do debugging if necessary (link gdb tutorials) when using a dev version?
Kdenlive warns me about missing codecs, I cannot render in some formats.
There are several possible reasons for this:
  1. You have installed the codecs after Kdenlive's installation. To force Kdenlive to check available codecs on your system, run the configuration wizard: Settings -> Run Config Wizard. Complete the wizard and restart Kdenlive to be sure that codecs have been detected.
  2. The codecs are not available on your system. Kdenlive uses the codecs from your FFmpeg or Libav library. Due to some licensing issues, some distributions do not provide all codecs by default and you might need to install an extra package. On Ubuntu / Mint for example, you must install a package called libavcodec-extra-xx. After that, check again the codecs as explained in the first step.
  3. Last possibility is that your FFmpeg or Libav version is buggy and does not report all supported codecs. Kdenlive releases after 0.9.2 have an option to try using codecs even if they seem unsupported: Settings -> Configure Kdenlive and check the Bypass codec verification option.
Kdenlive er for stor på min skærm. Jeg kan ikke gøre den mindre.
Dette sker som regel når der er for mange kontroller åbne. Hver kontrol optager en vis mindste bredde. Luk nogle af dem (f.eks. via menuen Vis) og overvej at bruge layouts (Vis -> Gem layout som).
Jeg vil trimme videoer uden at genindspille dem. Hvordan kan jeg gøre det?
Det kan du ikke med Kdenlive. (Prøv i stedet Avidemux). Årsagen er at ved opsplitning skal filer håndteres på en ganske anderledes måde (filen selv skal ændres, hvor Kdenlive renderer frames til en ny fil).
Se også [1], [2]
Jeg vil anvende en effekt, for eksempel et vandmærke, på hele projektet. Hvad er den bedste måde at gøre det?
Lav et nyt projekt med samme projektprofil og importér det projekt, som du vil anvende effekten på som et klip (Projekt -> Tilføj klip).
Se også How to: Add a Watermark in kdenlive på Vimeo.
Min monitor afspiller forvrængede billeder eller gør generelt noget, som den ikke skulle.
Tjek Indstillinger -> Indstil Kdenlive... -> Afspilning. Prøv at slå OpenGL fra, hvis det er aktiveret eller brug en anden driver. Kdenlive skal måske genstartes.