Digikam/Check Database/ca: Difference between revisions

From KDE UserBase Wiki
(Updating to match new version of source page)
 
(8 intermediate revisions by one other user not shown)
Line 1: Line 1:
<languages />
<languages />


== Comprovar i optimitzar les bases de dades al digiKam ==
== Verificar i optimitzar les bases de dades al digiKam ==
Transcrit des de l'article d'en [[User:Dmitri Popov|Dmitri Popov]], el 19 de desembre de 2011
Transcrit des d'un article al blog d'en [[User:Dmitri Popov|Dmitri Popov]], el 19 de desembre de 2011


By default,'''digiKam''' uses two ''SQLite databases'' for storing essential data: ''digikam4.db'' and ''thumbnails-digikam.db''. And to make the application run fast and smoothly, it’s a good idea to check and optimize the databases every now and then. To do this on Ubuntu or its derivatives, you need to install the <tt>sqlite3</tt> package using the <code>sudo apt-get install sqlite3</code> command. Once you’ve done that, back up the digikam4.db and thumbnails-digikam.db databases. Open then the terminal and switch to the directory where the databases are stored. First off, you should check the integrity of both databases using the following commands:
By default, '''digiKam''' uses two ''SQLite databases'' for storing essential data: ''digikam4.db'' and ''thumbnails-digikam.db''. And to make the application run fast and smoothly, it’s a good idea to check and optimize the databases every now and then. To do this on Ubuntu or its derivatives, you need to install the <tt>sqlite3</tt> package using the <code>sudo apt-get install sqlite3</code> command. Once you’ve done that, back up the digikam4.db and thumbnails-digikam.db databases. Open then the terminal and switch to the directory where the databases are stored. First off, you should check the integrity of both databases using the following commands:


{{Input|1=sqlite3 -line digikam4.db 'pragma integrity_check;'
{{Input|1=sqlite3 -line digikam4.db 'pragma integrity_check;'
sqlite3 -line thumbnails-digikam.db 'pragma integrity_check;'}}
sqlite3 -line thumbnails-digikam.db 'pragma integrity_check;'}}


If both databases are in order, you should see the message {{Output|1=integrity_check = ok}}   
Si les dues bases de dades estan en ordre, hauríeu de veureu el missatge {{Output|1=integrity_check = ok}}   


To optimize the databases, run the two commands below:
Per optimitzar les bases de dades, executeu les dues ordres a continuació:


{{Input|1-sqlite3 -line digikam4.db 'vacuum;'
{{Input|1-sqlite3 -line digikam4.db 'vacuum;'
sqlite3 -line thumbnails-digikam.db 'vacuum;'}}
sqlite3 -line thumbnails-digikam.db 'vacuum;'}}


Run then the integrity check once again to make sure that everything works properly, and you are done.
Executeu a continuació la verificació de la integritat una vegada més per assegurar-vos que tot funciona correctament, i ja està.


[[Category:Graphics]]
[[Category:Gràfics/ca]]
[[Category:Fotografia/ca]]
[[Category:Fotografia/ca]]
[[Category:Tutorials]]
[[Category:Guies d'aprenentatge/ca]]

Latest revision as of 13:00, 4 July 2019

Other languages:

Verificar i optimitzar les bases de dades al digiKam

Transcrit des d'un article al blog d'en Dmitri Popov, el 19 de desembre de 2011

By default, digiKam uses two SQLite databases for storing essential data: digikam4.db and thumbnails-digikam.db. And to make the application run fast and smoothly, it’s a good idea to check and optimize the databases every now and then. To do this on Ubuntu or its derivatives, you need to install the sqlite3 package using the sudo apt-get install sqlite3 command. Once you’ve done that, back up the digikam4.db and thumbnails-digikam.db databases. Open then the terminal and switch to the directory where the databases are stored. First off, you should check the integrity of both databases using the following commands:

sqlite3 -line digikam4.db 'pragma integrity_check;'
sqlite3 -line thumbnails-digikam.db 'pragma integrity_check;'

Si les dues bases de dades estan en ordre, hauríeu de veureu el missatge

integrity_check = ok

Per optimitzar les bases de dades, executeu les dues ordres a continuació:

1-sqlite3 -line digikam4.db 'vacuum;'
sqlite3 -line thumbnails-digikam.db 'vacuum;'

Executeu a continuació la verificació de la integritat una vegada més per assegurar-vos que tot funciona correctament, i ja està.